How To Start A Stubborn Chainsaw

Starting a stubborn chainsaw can be a tricky and tedious process, especially for those who are not used to operating such machinery. However, there are a few steps that you can take to ensure that you start your chainsaw quickly and without too much trouble.

First of all, make sure that the fuel tank is filled with the correct mixture of oil and gasoline. Many chainsaws require a specific ratio of oil to gasoline, which should be stated in the user manual. If you are unsure of the correct ratio, it is best to consult the user manual or an expert.

Next, inspect the spark plug for any signs of damage or corrosion. If it is damaged or corroded, you should replace it. It is also important to check if the spark plug gap is the correct size. The gap should be set according to the user manual.

If the spark plug is in good condition, then you can proceed to the next step. Check the fuel filter to make sure that it is clean and free of any debris or dirt. If the fuel filter is clogged, then it should be replaced.

Once the spark plug and fuel filter are in good condition, you can now begin the process of starting the chainsaw. First, make sure that the choke is in the "on" position. This is usually indicated by a lever or switch located on the side or near the engine.

Next, you should pull the starter rope a few times in order to prime the engine. This will allow the fuel to flow through the system and into the engine. Once the engine has been primed, it is time to start the chainsaw.

To start the chainsaw, pull the starter rope until it feels tight and then release it quickly. If the engine does not start, then you may need to repeat this process a few times. If the chainsaw starts, then you can move to the next step.

Once the chainsaw is running, you can adjust the choke to the "off" position. This will allow the engine to run at a higher speed and will make it easier to use the saw.

Finally, if the chainsaw is still not starting, then you may need to adjust the carburetor. This should also be done according to the instructions in the user manual.

By following these steps, you should be able to start your stubborn chainsaw quickly and without too much trouble. Just remember to always consult the user manual for instructions and to properly maintain the chainsaw for optimal performance. Good luck!

Chainsaw is HARD TO START Try this EASY TRICK, especially on the BIG Stihl's, Echo's and Husqvarna!

How To Start A Stubborn Chainsaw. Today we go over cold starting BIG saws and my tricks to make it WAY EASIER!! Thanks for tuning back into Chickanic! If you found this video helpful, please LIKE, SUBSCRIBE and COMMENT!! If you would like to send me a gift to my house, find my Amazon Wish List HERE! amazon.com/hz/wishlist/ls/G5FF73Q3T94D?ref_=wl_share Buy your own Chickanic...

Stihl Chainsaw Won't Start - The Reason Why Surprised Me - YouTube

Starting a Stihl Chainsaw the correct way. NEVER flood it Again!

This same principle will work for all of Stihl engines including weedeaters, trimmers, etc.

Chainsaw WON'T START or HARD to START Try these easy fixes!

If your chainsaw is HARD to START, or WON'T actually start at all, then this video has a practical easy to follow procedure for you to follow. A vital tool in your toolbox is knowledge. Without knowledge, no one can fix anything. For a FREE Printable Download help check Leaflets: therepairspecialistonline.com/ These downloads are from my...

Quickly UNFLOOD YOUR CHAINSAW Using NO Tools

QUICKLY unflood your chainsaw using NO TOOLS!! Maybe you over choked the engine by mistake! Now it's flooded and won't start. Easy way to unflood it and get back to work...this also applies to weedeaters, lawn mowers, blowers, etc. 👍Please click the like button and tell me what you think of this video in the comments section below....

421K views 3 years ago If your chainsaw is HARD to START, or WON'T actually start at all, then this video has a practical easy to follow procedure for you to.

How To Start A Stubborn Chainsaw.